|
|
 |
INSTALLATION:
What you need.
-
Sat Cruiser DSR-101 Receiver with remote control.
- Audio
cables:
- RCA male to RCA male (receiver to balancing amplifier).
- XLR
to console interface (balancing amplifier to switcher/console
input).
- Unbalanced
to Balanced audio converter.
- In-line
coaxial DC Block (if LNB DC power is provided by another
receiver).
- Television
or monitor with video or RF (channel 3) input for receiver
setup.
- 3.1-3.8
meter (10-12 feet) Solid 2° compliant satellite dish.
- Digital
ready PLL LNB (<25°).
- Receiver
authorization codes.
- Receiver
will not decode USA Radio Network audio without proper
authorization codes. These codes will be given only after
confirmation of an executed affiliation agreement with
the network.
- Dish
installation and alignment.
- Dish
must be installed and properly aligned with a digital
spectrum analyzer before proceeding to hardware setup.
Please refer to www.dvb-radio.net for detailed procedures.
Hardware
Setup:
Connect
Receiver as Shown in the Setup Diagram. Do not connect the
coax from the LNB to the Digital input on the receiver yet (LNB
coax will be connected after LNB power "on/off" is configured).
Figure
1-Typical Hardware Setup
Installation Procedure:
Obtain
receiver authorization codes by calling the USA Radio Network
Affiliate Relations Department at 800-829-8111 ext. 1338.
Stations must have an executed contract with the USA Radio
Network before authorization codes will be released.
Connect
Equipment & Power-up:
Connect equipment as shown in Figure 1. DO NOT CONNECT THE COAX TO THE RECEIVER UNTIL LNB POWER HAS BEEN PROGRAMMED (see Configure LNB Power section below).
Turn the power on for the television and receiver. The MAIN MENU should appear on the television.
Helpful Basic Remote Control Hints:
- The
Text panels in the on-screen menus behave as "buttons"
to be selected.
- "CH
UP/CH DN"-jump between selections in a menu.
- "VOL
LT/VOL RT"-jump between menus when more than one menu is
visible or moves cursor left/right within a data field.
- Use
the "OK" button to select the choice.
- Use
"CLEAR" to erase the contents of a numeric field.
- Use
the "MENU" button to return to previous menus.
Configure
LNB Power:
Select the Installation button in the Main Menu, then select
the LNB Power button. If LNB Power is supplied from another
receiver, set LNB Power to OFF. If LNB Power is to be supplied
by the Sat Cruiser, set LNB Power to ON. Return to the Installation
menu by pressing the Menu key.
Connect LNB Cable:
Connect LNB cable from dish to the Digital input on the rear
of the receiver (figure 1).
Set TP (Transponder) Configuration:
Select the TP Configuration button from the Main Menu and
press "OK".
Select Satellite Name:
Select the Satellite button of the TP Configuration menu and
press "OK".
Choose the name of the satellite: AMC3_C and press "MENU"
to return to the Installation Menu.
Verify/Set LNB Parameters:
AMC3_C
or USER1 (GE-8) |
| LNB
Type |
Standard |
| LO.
Freq |
05150 |
| LO.Freq.Low |
|
| 22KHz. |
OFF |
| DISEqC
mode |
Disable |
| DISEqC
1.2 |
OFF |
| 0/12V
Switch |
|
Figure2-Typical
LNB Settings
Select the LNB button of the TP for Satellite Configuration
menu press "OK". This displays the current settings
for the LNB.
Verify that the parameters are correct for the LNB
used on the dish. The default parameters shown in
figure 2 are typical for most C-Band LNB converters.
Make any changes as needed.
When the LNB parameters are correct, press the "MENU"
button to return to the TP configuration Menu.
Add Transponder Parameters:
AMC3_C
or USER1 for GE-8 |
| Frequency |
00000
(enter frequency provided by Network) |
| Polarization |
Auto |
| Symbol
Rate |
00000
(enter symbol rate provided by Network) |
| FTA
only |
No |
| DISEqC
1.2 |
|
| Search
Channels |
|
| Network
Search |
|
| Add
Channel |
Move
cursor HERE and press "OK" button on remote
to register settings above. |
Figure
3-Transponder Parameter Entry Table
From the TP Configuration menu, press VOL RT to
highlight the Add button.
Press "OK" to enter data for the transponder[s]
for the satellite you selected earlier.
The transponder parameters entry table will be displayed
(figure 3).
NOTE: When
entering a 4-digit number in a 5-digit field you
must precede the number with a leading "0".
Example: frequency is 4050 MHz. Enter "04050".
Fill in the Frequency with the carrier frequency
and push CH DOWN to move to the Polarization field.
The ‘S’ signal indicator bar below the
table should now be active.
Set Polarization to Auto and push CH DOWN to move
to the Symbol Rate field.
Fill in the Symbol Rate and push CH UP to move to
the FTA-Only field. The FTA-Only should be set to ‘No’.
Once all these setting are correct, from use the
CH DOWN to move to the Add Channel field and PRESS
"OK" 1 TIME ONLY!
Pressing the OK button in the ‘Add Channel’ data
field displays the ‘Add Channel’ entry
table. Individual channels for the satellite entered
can now be programmed using the ‘Add Channel’ entry
table displayed.
Add Channel:
| Channel
Name |
US1 |
| Video
PID |
|
| Audio
PID |
0123 |
| PCR
PID |
4567 |
| Add |
|
Figure
4-Add Channel Entry Table
Each channel added to the transponder is given
a name, an Audio PID number and a PCR PID number.
Using the remote, select the data field to the
right of the channel name and press OK. A set
of characters
is displayed. Choose the characters for the name
of the channel. For example, you might use US1
for USA channel 1, US2 for USA channel 2, US3
for USA
channel 3, and US4 for USA channel 4.
Helpful hints for entering Channel Names:
- Use
the arrow keys on the remote to move to the
letter to add.
- Press
OK to add the highlighted character to the
name field.
- INFO
toggles the character set displayed between
alphabetic and numeric character sets.
- Press
MENU when name entry is complete to return
to the ‘Add Channel’ entry table.
The Channel name is now displayed in the Table.
Leave
the Video PID field Blank. Use CH DOWN to move
to the Audio PID field.
Enter the confidential Audio PID number - Highlight
the field to the right of ‘Audio PID’,
press OK, and enter the four digit number using
the numeric keys on the remote. Press OK to
register the Audio PID number.
Enter the confidential PCR PID number - Highlight
the field to the right of ‘PCR PID’,
press OK, and enter the four digit number using
the numeric keys on the remote. Press CH DOWN
to move to the ‘ADD channel’ field.
PRESS "OK" ONE TIME ONLY!
This adds the new channel information to the
transponder. The number of channels added so
far will be displayed in the field to the right
of the ‘Add channel’ prompt.
Press MENU to return to the Transponder Parameter
Entry Table.
Press MENU again to return to the ‘TP
Installation’ menu.
Press MENU again to return to the ‘Main
Menu’.
|
 |
|
